excavator bucket teeth

We are professional excavator bucket teeth suppliers Excavator bucket teeth are important consumable parts on excavators, similar to human teeth. They are combined bucket teeth composed of tooth bases and tooth tips, which are connected by pins. Since the worn out part of the bucket teeth is the tip of the tooth, just replace the tip. Classification according to the environment in which the bucket teeth of the excavator are used. Excavator bucket teeth can be divided into rock teeth (for iron ore, quarry, etc.), earthwork teeth (for excavating soil, sand, etc.), conical teeth (for coal mines). According to the bucket tooth seat: the excavator bucket tooth can be divided into vertical pin bucket tooth (mainly Hitachi excavator), horizontal pin bucket tooth (Komatsu excavator, Carter excavator, Daewoo excavator, Kobelco excavator, etc.) , Rotary bucket teeth (V series bucket teeth).

The function of the oil filter is to caterpillar filters out the sundries, gums and moisture in the oil, and deliver clean oil to each lubricating part. In order to reduce the frictional resistance between the relatively moving parts in the engine and reduce the wear of the parts, the oil is continuously transported to the friction surface of each moving part to form a lubricating oil film for lubrication. The engine oil itself contains a certain amount of gum, impurities, moisture and additives. At the same time, during the working process of the engine, the introduction of metal wear debris, the entry of debris in the air, and the generation of oil oxides make the debris in the oil gradually increase. If the oil directly enters the lubricating oil circuit without being filtered, the sundries contained in the oil will be brought into the friction surface of the moving pair, which will accelerate the wear of parts and reduce the service life of the engine.

Caterpillar excavator filter maintenance 1. The caterpillar oil filters is the core component of the filter. It is made of special materials and is a wearing part, which requires special maintenance and maintenance; 2. When the caterpillar oil filters has been working for a long time, the filter element has intercepted certain impurities, which will lead to an increase in pressure and a decrease in flow. At this time, it needs to be cleaned in time;

The working environment of excavators is generally harsh and dusty. The excavator air filter is mainly used to protect the corresponding parts of the excavator, reduce the entry of impurities and dust, improve the work efficiency of the excavator and prolong the service life. There are many types of excavator filter elements, the common types are excavator air filter, air conditioning filter element, hydraulic oil pipeline filter element, fuel filter element, hydraulic oil return filter element, pilot filter element, hydraulic oil suction filter element, etc. These filter elements play an important role in the maintenance of excavators. play an important role.

Excavators are most prone to high water temperature failures. Today, I shared with you the high water temperature failure caused by theexcavator water pump. How to check if the excavator water pump is working? Remove the thermostat, turn it on, run at idle speed and high speed repeatedly, press the water pipe to see if there is water passing through the water pipe, if the water pipe is hard, it means the pressure is normal, then open the water tank cover and observe whether the water flow speed is normal. What should I do if the excavator water pump leaks? Open the top cover, disassemble the fan water blocking ring, check the inside of the water pump belt, open the bottom plate of the oil pan, and confirm the specific leakage location. If the oil seal of the water pump and the pad of the water pump are damaged, they can be replaced directly.

excavator engine parts contains: 1set Full Gasket set 4pcs Liner Cylinder 4pcs Piston,STD size. 4pcs Piston Pin 4set Ring set for 4pistons.STD size. 1set Crankshaft bearing STD size Or over size +0.25 /0.5mm 1set Connect Rod Bearing, STD size Or over size +0.25 /0.5mm Note : Please confirm which size you need For the bearing set ,If no extal Requirement we will send STD Size ,Thanks. Application:Excavator

Material：high quality 40cr steel round bar is the raw material of our excavator tooth pin. Surface: Various surface treatment for our excavator tooth pin like blackening,galvanied... Products: Complete product system of all kinds of excavator tooth pins. We can manufact all the tooth pins you need.

The bucket tooth adapter structure is mainly composed of three parts, the head, the upper leg and the lower leg. The head cooperates with the inner cavity of the bucket tooth sleeve to become the mounting seat of the bucket tooth sleeve. The front ends of the upper and lower legs are both connected with the rear end of the head.

Our company has been selling Kubota excavator bucket teeth for many years and has accumulated rich experience in the long-term market. Our Kubota bucket teeth are available in a variety of quality levels. And our sales will recommend to you the most economical choice according to your application scenario. Make your excavator more efficient.